Avery MPI2923 Matte Gray Permanent

Description

Avery MPI2923 Matte Gray Permanent
Avery Dennison® MPI 2923 Matte Easy Apply™
Matte White Polymeric Calendered Vinyl
Features
•
•
•
•
•
•
•
•
•
•
Matte white polymeric calendered vinyl film offering a cost effective solution for
your intermediate outdoor graphic needs
Easy Apply™ adhesive technology with air egress channels to easily eliminate
bubbles and wrinkles during application
Excellent printability across a range of technology and inks
Matte finish for low glare appearance
StaFlat™ liner provides excellent handling and converting properties
Reliable outdoor durability and performance
Very good dimensional stability after application
Grey adhesive provides extra opacity for blockout performance
Permanent adhesive for excellent adhesion to most surfaces
Compatible with the Avery Dennison DOL 2000 series overlaminates
Description
Film: 86 micron matte white
polymeric calendered vinyl
Adhesive: Grey permanent
acrylic with Easy Apply™
Technology
Backing: Two side PE coated
StaFlat™ paper, 145g/m2
Outdoor life**: Up to 5 years
(unprinted)
Application surface: Flat,
simple curves
Common Applications
•
•
•
•
•
•
Outdoor signage
Point of purchase
Outdoor advertising
Indoor advertising
Exhibition graphics
Vehicle Graphics (Flat or Simple
Curved Surfaces)
Conversion+

Flat bed cutters Cold overlaminating
Friction fed cutters Electrostatic printing
Die cutting Latex inkjet
Thermal transfer Eco solvent inkjet
Screen printing Solvent inkjet
Offset printing UV curable inkjet
+
Always test with your combination of printer and inks prior to commercial use.
Uses
Avery Dennison MPI 2923 Matte Easy Apply is a matte white polymeric calendered vinyl film designed for ease
of application on a wide range of intermediate outdoor and general signage applications and vehicles graphics
with flat or simple curved surfaces, and where good outdoor durability, high opacity and good print quality are
required.
Application
• Avery Dennison Graphics recommends a maximum total ink limit of 270% to ensure optimal performance.
• Dry application only. Do not use water and detergent or a commercial application fluid to position the graphic.
• Refer to Instructional Bulletins 1.01, 1.4, 4.06 & 4.14 for printing, laminating and application instructions.
Avery Dennison Graphics Solutions Asia Pacific
www.graphicsap.averydennison.com
Chemical
Resistant to most mild acids, alkalies and salt solutions.
General
Calliper, face film ISO 534 86 micron
Calliper, face film & adhesive ISO 534 111 micron
Dimensional stability DIN 30646 0.6mm max.
Gloss Hunter Gloss at 60° 15
Adhesion, initial FINAT FTM-1, stainless steel 700 N/m
Adhesion, ultimate FINAT FTM-1, stainless steel 962.5 N/m
Flammability AS/NZS 3837:1998
ISO 5660-1:2002
Group 1
Group 1-S
Shelf life Stored at 20-25° C / 45-55 % RH 2 years
Expected Durability ** Vertical exposure ^ Up to 5 years (unprinted)
^ See ICS Performance Guarantee Durability Bulletin for your
specific printer and ink combination for further information
Note
Materials have to be properly dried and cured before further processing, like laminating,
varnishing, trimming, contour cutting or application. The residual solvents can otherwise
change the products’ specific features and properties.
Thermal
Application temperature Minimum: + 10o
C
Temperature range – 40o
C to + 82o
C
Important
Information on physical characteristics is based
upon tests we believe to be reliable. The values
listed herein are typical values and are not for use
in specifications.
They are intended only as a source of information
and are given without guarantee and do not
constitute a warranty. Purchasers should
independently determine, prior to use, the
suitability of any material for their specific use.
All technical data is subject to change without
prior notice.
Warranty
Avery Dennison® materials are manufactured
under careful quality control and are warranted to
be free from defect in material and workmanship.
Any material shown to our satisfaction to be
defective at the time of sale will be replaced
without charge. Our aggregate liability to the
purchaser shall in no circumstances exceed the
cost of the defective materials supplied. No
salesman, representative or agent is authorised
to give guarantee, warranty, or make any
representation contrary to the foregoing.
All Avery Dennison® materials are sold subject to
the above conditions, being part of our
standard conditions of sale, a copy of which is
available on request.
**Expected Durability
The expected durability of Avery Dennison films
are defined as the expected performance life of
the Avery Dennison graphic film(s) within Zone 1
of the Avery Dennison zone system, in outdoor
vertical exposure conditions.
The actual performance life will depend on a
variety of factors, including selection and
preparation of substrate, angle and direction of
exposure, application methods, environmental
conditions and cleaning/maintenance of the films.
In case of films used in areas of high
temperatures or humidity, high altitudes and
industrially polluted areas the performance will be
further reduced.
Expected Durability and Warranted Period
Definitions
Expected durability is the expected period of
time defined in the product data sheet, the
product should, but is not warranted to, perform
satisfactorily when applied in vertical exposure
conditions as defined in Instructional Bulletin
1.30. The warranted period as defined in the
appropriate ICS Performance Guarantee Bulletin,
is the maximum period of time Avery Dennison
will warrant the finished products performance in
accordance with ICS Performance Guarantee
Terms and Conditions 1.0, provided that the film
is properly stored, converted and installed in
accordance with Avery Dennison guidelines.
+
Compatible with most printer and ink
combinations. Test prior to use.
Avery Dennison® MPI 2923 Matte Easy Apply™ Rev. 5 (Jan 2018)
Dimensional stability:
Is measured on a 150 x 150 mm aluminium panel to
which a specimen has been applied; 72 hours after
application the panel is exposed for 48 hours to + 70°C,
after which the shrinkage is measured.
Adhesion:
(FTM-1, FINAT) is measured by peeling a specimen at a
180° angle from a stainless steel or float glass panel, 24
hours after the specimen has been applied under
standardised conditions. Initial adhesion is measured 20
minutes after application of the specimen.
Flammability:
A specimen applied to aluminium is subjected to the
flame of a gas burner for 15 seconds. The film should
stop burning within 15 seconds after removal from the
flame.
Temperature range:
A specimen applied to stainless steel is exposed at high
and low temperatures and brought back to room
temperature. 1 hour after exposure the specimen is
examined for any deterioration. Note: Prolonged
exposure to high and low temperatures in the presence of
chemicals such as solvents, acids, dyes, etc. may
eventually cause deterioration.
Chemical Resistance:
All chemical tests are conducted with test panels to which
a specimen has been applied. 72 hours after application
the panels are immersed in the test fluid for the given test
period. 1 hour after removing the panel from the fluid, the
specimen is examined for any deterioration.
Corrosion Resistance:
A specimen applied to aluminium is exposed to saline
mist (5% salt) at 35ºC. After exposure, the film is removed
and the panel is examined for traces of corrosion.
Test Methods
A113391 MPI2923 MATTE GPRM SF 60″
A113389 MPI2923 MATTE GPRM SF 54″
A001411 MPI2923 MATTE GPRM SF 48X50 YDS 3IN
A001413 MPI2923 MATTE GPRM SF 60X50 YDS 3IN
A005281 MPI2923 MATTE GPRM SF 54X100 YDS 3IN
A002493 MPI2923 MATTE GPRM SF 54X50 YDS 3IN
A002467 MPI2923 MATTE GPRM SF 30X50 YDS 3IN
A010515 MPI2923 MATTE GPRM SF 54X5

319107A60R A113391 MPI2923 MATTE GPRM SF 60″
319107A54R A113389 MPI2923 MATTE GPRM SF 54″
3273 A001411 MPI2923 MATTE GPRM SF 48X50 YDS 3IN
3275 A001413 MPI2923 MATTE GPRM SF 60X50 YDS 3IN
6109 A005281 MPI2923 MATTE GPRM SF 54X100 YDS 3IN
41036 A002493 MPI2923 MATTE GPRM SF 54X50 YDS 3IN
41008 A002467 MPI2923 MATTE GPRM SF 30X50 YDS 3IN
0 A010515 MPI2923 MATTE GPRM SF 54X5